diff --git a/doc/source/guides/neutron.rst b/doc/source/guides/neutron.rst
index e99a143..5891f68 100644
--- a/doc/source/guides/neutron.rst
+++ b/doc/source/guides/neutron.rst
@@ -72,98 +72,6 @@
 
 
 
-
-
-Using Neutron with Multiple Interfaces
-======================================
-
-The first interface, eth0 is used for the OpenStack management (API,
-message bus, etc) as well as for ssh for an administrator to access
-the machine.
-
-::
-
-        stack@compute:~$ ifconfig eth0
-        eth0      Link encap:Ethernet  HWaddr bc:16:65:20:af:fc
-                  inet addr:192.168.1.18
-
-eth1 is manually configured at boot to not have an IP address.
-Consult your operating system documentation for the appropriate
-technique. For Ubuntu, the contents of `/etc/network/interfaces`
-contains:
-
-::
-
-        auto eth1
-        iface eth1 inet manual
-                up ifconfig $IFACE 0.0.0.0 up
-                down ifconfig $IFACE 0.0.0.0 down
-
-The second physical interface, eth1 is added to a bridge (in this case
-named br-ex), which is used to forward network traffic from guest VMs.
-Network traffic from eth1 on the compute nodes is then NAT'd by the
-controller node that runs Neutron's `neutron-l3-agent` and provides L3
-connectivity.
-
-::
-
-        stack@compute:~$ sudo ovs-vsctl add-br br-ex
-        stack@compute:~$ sudo ovs-vsctl add-port br-ex eth1
-        stack@compute:~$ sudo ovs-vsctl show
-        9a25c837-32ab-45f6-b9f2-1dd888abcf0f
-            Bridge br-ex
-                Port br-ex
-                    Interface br-ex
-                        type: internal
-                Port phy-br-ex
-                    Interface phy-br-ex
-                        type: patch
-                        options: {peer=int-br-ex}
-                Port "eth1"
-                    Interface "eth1"
-
-
-
-
-
-Neutron Networking with Open vSwitch
-====================================
-
-Configuring neutron, OpenStack Networking in DevStack is very similar to
-configuring `nova-network` - many of the same configuration variables
-(like `FIXED_RANGE` and `FLOATING_RANGE`) used by `nova-network` are
-used by neutron, which is intentional.
-
-The only difference is the disabling of `nova-network` in your
-local.conf, and the enabling of the neutron components.
-
-
-Configuration
--------------
-
-::
-
-        FIXED_RANGE=10.0.0.0/24
-        FLOATING_RANGE=192.168.27.0/24
-        PUBLIC_NETWORK_GATEWAY=192.168.27.2
-
-        disable_service n-net
-        enable_service q-svc
-        enable_service q-agt
-        enable_service q-dhcp
-        enable_service q-meta
-        enable_service q-l3
-
-        Q_USE_SECGROUP=True
-        ENABLE_TENANT_VLANS=True
-        TENANT_VLAN_RANGE=1000:1999
-        PHYSICAL_NETWORK=default
-        OVS_PHYSICAL_BRIDGE=br-ex
-
-In this configuration we are defining FLOATING_RANGE to be a
-subnet that exists in the private RFC1918 address space - however in
-in a real setup FLOATING_RANGE would be a public IP address range.
-
 Neutron Networking with Open vSwitch and Provider Networks
 ==========================================================
 
@@ -206,6 +114,48 @@
         }
 
 
+On a compute node, the first interface, eth0 is used for the OpenStack
+management (API, message bus, etc) as well as for ssh for an
+administrator to access the machine.
+
+::
+
+        stack@compute:~$ ifconfig eth0
+        eth0      Link encap:Ethernet  HWaddr bc:16:65:20:af:fc
+                  inet addr:10.0.0.3
+
+eth1 is manually configured at boot to not have an IP address.
+Consult your operating system documentation for the appropriate
+technique. For Ubuntu, the contents of `/etc/network/interfaces`
+contains:
+
+::
+
+        auto eth1
+        iface eth1 inet manual
+                up ifconfig $IFACE 0.0.0.0 up
+                down ifconfig $IFACE 0.0.0.0 down
+
+The second physical interface, eth1 is added to a bridge (in this case
+named br-ex), which is used to forward network traffic from guest VMs.
+
+::
+
+        stack@compute:~$ sudo ovs-vsctl add-br br-ex
+        stack@compute:~$ sudo ovs-vsctl add-port br-ex eth1
+        stack@compute:~$ sudo ovs-vsctl show
+        9a25c837-32ab-45f6-b9f2-1dd888abcf0f
+            Bridge br-ex
+                Port br-ex
+                    Interface br-ex
+                        type: internal
+                Port phy-br-ex
+                    Interface phy-br-ex
+                        type: patch
+                        options: {peer=int-br-ex}
+                Port "eth1"
+                    Interface "eth1"
+
 
 Service Configuration
 ---------------------